Posted on

Erin’s status report for 03/30/24

What did you personally accomplish this week on the project? Give files or photos that demonstrate your progress. Prove to the reader that you put sufficient effort into the project over the course of the week (12+ hours).

I soldered all the electronics in the bottle this week. I am also writing the app side bluetooth protocol and parsing.

Is your progress on schedule or behind?

On schedule.

What deliverables do you hope to complete in the next week?

I hope to focus on the demo and have a mvp for the demo.

Posted on

Alan’s status report for 03/30/24

What did you personally accomplish this week on the project? Give files or photos that demonstrate your progress. Prove to the reader that you put sufficient effort into the project over the course of the week (12+ hours).

This week, I mostly worked on fabricating the bottle for the interim demo. I planned and drilled holes for the sensors, and sealed them in place with our food-safe sealant. It took a few days (the curing time for the sealant is 24 hours) and about three layers, but we now have a leak-free bottle! I also worked with Erin on soldering our circuit so we would no longer need a breadboard (she did most of the soldering; I did some of it, supported her on pieces that took two people, helped with planning for the circuit, modified the code to make connections easire, and tested the sensors once they had been soldered).

Is your progress on schedule or behind?

On schedule.

What deliverables do you hope to complete in the next week?

At the start of next week, I’ll focus on the interim demo – rehearsing my part of the presentation, helping define content, and troubleshoot any issues that come up so we can do to have a successful presentation.

I also plan on working some on connecting the battery, on working with Erin on the app to parse bluetooth data and implement the classifying logic in the app, and on the mechanism for testing whether the bottle is upright. We may need to purchase more pressure pads for this last part. I will also work on waterproofing solutions for the circuits in the bottom compartment (in case the sealant becomes leaky, which should not happen, but we will add a contingency measure to protect our circuit better).

Photo of fabricated bottle, holding water:

Posted on

Team’s Status Report for 03/30/24

What are the most significant risks that could jeopardize the success of the project? How are these risks being managed? What contingency plans are ready?

We are working on integration, and the two main issues right now are fitting all the needed components into the bottle’s bottom chamber and detecting density and uprightness. For fitting all components, we are shortening wires as much as possible, and looking into fabricating a larger chamber.

For density and uprightness, we noticed that we couldn’t attach our pressure sensor directly to the bottom of our bottle, since it is slightly indented and the sensors are somewhat fragile when bent. Thus, we plan on fabricating an adapter (as was suggested to us in the weekly meeting) to improve that. We may need more pressure plates to work on this.

Were any changes made to the existing design of the system (requirements, block diagram, system spec, etc)? Why was this change necessary, what costs does the change incur, and how will these costs be mitigated going forward?

We will need to purchase more pressure plates, but that is well within the budget; similarly, we plan on fabricating the adapter for the sensor and a larger bottom compartment, but we have access to printers we can use at no cost.

Here’s the bottle, with mounted sensors, that we assembled this week and will use for our interim demo:

Posted on

Matthew’s status report 3/30/2024

What did you personally accomplish this week on the project? Give files or photos that demonstrate your progress. Prove to the reader that you put sufficient effort into the project over the course of the week (12+ hours).

I made CAD models of all of the assembled parts and 3d printed components to extend the bottom of the water bottle, as well as to hold the ultrasonic in place.

Is your progress on schedule or behind?

We are on schedule.

What deliverables do you hope to complete in the next week?

I hope to complete an MVP model and have a functioning product for the presentation

Posted on

Matthew’s status report 3/23/2024

What did you personally accomplish this week on the project? Give files orphotos that demonstrate your progress. Prove to the reader that you put sufficienteffort into the project over the course of the week (12+ hours).

I discussed compressing the number of components we truly needed to get our MVP to work and helped the team limit the design of the bottle to only use 1 microcontroller placed at the very bottom of the water bottle. I also drew out a schematic of the final microcontroller setup, and discussed options on setting up the ultrasonic without having to place it at the very top of the bottle.

 

• Is your progress on schedule or behind? If you are behind, what actions will betaken to catch up to the project schedule?

We are on schedule

• What deliverables do you hope to complete in the next week?

We hope on having the CAD MVP product and work on directly connecting wires instead of a breadboard

Posted on

Erin’s Weekly Status Update 3/23

What did you personally accomplish this week on the project? Give files or photos that demonstrate your progress. Prove to the reader that you put sufficient effort into the project over the course of the week (12+ hours).

This week I wrote the app side code to connect the bottle to the app via bluetooth. Alan & I designed the bluetooth protocol for the bottle to app connection. Finally, I wrote app backend code to save past state data for water intake in the actual db and fixed some styling issues.

Is your progress on schedule or behind? If you are behind, what actions will be taken to catch up to the project schedule?

On schedule

What deliverables do you hope to complete in the next week?

I hope to complete the bottle to app communication protocol and test it next week.  I also hope to make the calendar show different months instead of just the current one. I will support Matt and Alan once app mvp is done.

Posted on

Team Status Report for 03/23/24

What are the most significant risks that could jeopardize the success of the project? How are these risks being managed? What contingency plans are ready?

Currently, the main risks are physical – we have cadded and will print needed components to assemble our mvp for demonstration. We will need to carefully insulate non-waterproof electronics, make sure all components are securely in place, and sensors are properly secured as to provide reliable readings.

Were any changes made to the existing design of the system (requirements, block diagram, system spec, etc)? Why was this change necessary, what costs does the change incur, and how will these costs be mitigated going forward?

We made several changes over this week. We added turbidity and total dissolved solids sensors, and removed the capacitance sensor, as we found much more significant changes and less overlap in the liquids we want to classify. We also changed the system to use a single Adafruit ItsyBitsy board, rather than two. This is because all sensors we are using can be connected to a single board, and we changed the ultrasound to be attached to the body of the bottle rather than the lid. This will allow us to reduce power consumption, simplify the power supply systems, increase communication reliability (as we only need to communicate with a single board) and simplify communication logic (as we don’t need to synchronize data from two sources).

The cost of the added sensors is well within budget, and the other changes do not incur costs.

Updated schedule:

Posted on

Alan’s status report for 03/23/24

What did you personally accomplish this week on the project? Give files or photos that demonstrate your progress. Prove to the reader that you put sufficient effort into the project over the course of the week (12+ hours).

This week, I accomplished a few things for the project:

1-Added Total Dissolved Solids and Turbidity sensor to the circuit, and tested them, finding significant differences in the liquids tests (water, milk, and coffee).

2-Re-wired the circuit to use a single Adafruit ItsyBitsy Arduino board, rather than 2.

3-Improved the ble connection, writing a TCP-like protocol that waits for requests and waits for acknowledgement from the recipient.

4-Tested with different liquids (milk, water, coffee) for color, TDS, and turbidity, finding significant differences.

5-Wrote a vector-distance based classifier in python, to differentiate liquids.

 

Is your progress on schedule or behind? If you are behind, what actions will be taken to catch up to the project schedule?

On schedule

What deliverables do you hope to complete in the next week?

For the next week, I will fabricate the bottle, placing the sensors and holding them in place with sealant (as one of my current problems for testing is that I need to hold all sensors in place to get the readings), and work with Matthew to integrate with the cadded parts. I will also work with Erin on the app, to process ble packages and do the classifying logic in the app itself. Finally, I will plan and rehearse the interim demo, to identify potential issues and make sure it goes smoothly.

 

BLE communication (Adafruit ItsyBitsy <-> Bluefruit app on my Android phone):

Posted on

Matthew’s status report 3/16

What did you personally accomplish this week on the project? Give files or photos that demonstrate your progress. Prove to the reader that you put sufficient effort into the project over the course of the week (12+ hours).

I tested the new ultrasonic and capacitance measurements over several different liquids and types of cups to determine a correlation between capacitance and the liquid/cup material. Doing so required soldering the copper tape to wires, as well as setting up arduino code to accurately measure capacitance.

• Is your progress on schedule or behind? If you are behind, what actions will be taken to catch up to the project schedule?

Behind schedule, since the ultrasonic that we received was bugged, returning a constant value only

• What deliverables do you hope to complete in the next week?

I plan on having the ultrasonic and capacitance all working so that we can begin making an overall draft for the MVP, and start to turn the data we receive into more user friendly pieces of data such as volume

Posted on

Erin’s Status Report Week of March 16

What did you personally accomplish this week on the project? Give files or photos that demonstrate your progress. Prove to the reader that you put sufficient effort into the project over the course of the week (12+ hours).

This week, I worked on bluetooth code for the app side. I was able to create a bluetooth manager object in the app and a tester page for it. Using that I was able to work with Alan to connect the app to the arduino. To do this I also had to set up the app onto my iPhone which took some additional time.

• Is your progress on schedule or behind? If you are behind, what actions will be taken to catch up to the project schedule?

On schedule

• What deliverables do you hope to complete in the next week?

Over the next week, I plan on writing more of the app for the bluetooth page as well as more of the backend data structure for the app.